Sailfish 30-06 CC Ballston Spa NY

The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Boat House
(518) 393-5711
2855 Aqueduct Rd
Schenectady, NY
Services
Boat House

Data Provided by:
Point Breeze Marine
(518) 587-3397
1459 Rt. 9-P
Saratoga Springs, NY
 
Boat Mart
(518) 584-2628
549 Union Avenue
Saratoga Springs, NY
 
Maynard Yacht Brokers
(518) 399-3062
8 Main Street P.O. Box 109
Rexford, NY
 
Boat N R V Warehouse
(518) 371-7878
1208 Route 146
Clifton Park, NY
 
Saratoga Boat Works
(518) 584-2628
549 Union Avenue
Saratoga Lake, NY
 
Andersen Boat Shop
(518)399-5003 (518)399-4241
883 Route 50
Burnt Hills, NY
 
Brian'S Marine & Recreation
(315) 858-3400
3 Bronner St
Rexford, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Mohawk Valley Marine
(518) 399-2719
47 Mohawk Ave
Alplaus, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Alpin Haus Of Clifton Park
(518) 371-2211
103 Sitterly Road
Clifton Park, NY
Services
New Boat Sales, Used Boat Sales, Mobile Service, Engine Repair, Boat Storage, Back-in Test, Boat repair, In-Water Demos
Hours
M-F 9am-6pm Summer; Sat 9am-5pm

Data Provided by:

Sailfish 30-06 CC

Provided by:

Click here for more content from JDPower.com

Model Introduction
The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Construction
The skin coat of chop in DCPD resin goes down over the gelcoat, followed by a solid hull laminate of knit fiberglass in the sides and woven roving in the bottom. The hull is supported by a fiberglass, foam-cored Compsys stringer system, and the bulkheads are also foam-cored. The whole network is encapsulated in fiberglass and bonded to the hull. The transom is built of high-density poured foam-cored transom encapsulated in fiberglass. The hull-to-deck joint is bonded with urethane adhesive and stainless self-tapping screws every foot. The rubrail and the stainless insert follows with two more rows of screws fastening the joint. The one-piece cockpit/liner is bonded to the stringers with urethane putty, becoming an integral part of the boat's structure. The cabin liner is also bonded to the hull and to the cockpit liner where they meet at the aft cabin bulkhead. The Sailfish comes with a 10-year structural warranty that covers the hull against defects.

Hull Design
The Sailfish 30-06 CC has a deep-vee hull form with a sharp, deep entry and 24° of transom deadrise. Reverse running strakes (they turn up rather than down from garboard to chine), similar to the old Sea Craft hulls, run the length of the bottom. Its high freeboard increases seaworthiness, helping to prevent boarding seas, while providing high gunwale coamings inside the cockpit and a relatively high cockpit deck level above the waterline. ...

Click here to read the rest of the article at JDPower.com