Sailfish 30-06 CC Buffalo NY

The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Amherst Marine Center
(716) 691-6707
1900 Campbell Blvd
Buffalo, NY
Services
Amherst Marine Center

Data Provided by:
Ontario Marine Incorporated
(716) 883-2425
11 Summer St
Buffalo, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Marine Buffalo Associates Lp
(716) 853-4944
1 Hsbc Ctr Bsmt 1
Buffalo, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Olson Bros Marine Incorporated
(716) 821-0001
1111 Fuhrmann Blvd
Buffalo, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Small Boat Harbor-Olson Bros. Marine
(716) 821-0001
975 Furhmann Blvd.
Buffalo, NY
 
Raw Materials Company-Division Of International Marine Salva
(716) 895-6570
812 E Ferry St
Buffalo, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Windward Marine Yacht Sales
(716) 823-7769
1111 Fuhrmann Blvd
Buffalo, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Andersen Boat Shop
(518) 399-5003
Rt 50 Saratoga Rd
Buffalo, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Cjd & Associates
(716) 823-6341
1111 Fuhrmann Blvd
Buffalo, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Lower Lakes Marine Historical Society
(716) 849-0914
66 Erie St
Buffalo, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Data Provided by:

Sailfish 30-06 CC

Provided by:

Click here for more content from JDPower.com

Model Introduction
The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Construction
The skin coat of chop in DCPD resin goes down over the gelcoat, followed by a solid hull laminate of knit fiberglass in the sides and woven roving in the bottom. The hull is supported by a fiberglass, foam-cored Compsys stringer system, and the bulkheads are also foam-cored. The whole network is encapsulated in fiberglass and bonded to the hull. The transom is built of high-density poured foam-cored transom encapsulated in fiberglass. The hull-to-deck joint is bonded with urethane adhesive and stainless self-tapping screws every foot. The rubrail and the stainless insert follows with two more rows of screws fastening the joint. The one-piece cockpit/liner is bonded to the stringers with urethane putty, becoming an integral part of the boat's structure. The cabin liner is also bonded to the hull and to the cockpit liner where they meet at the aft cabin bulkhead. The Sailfish comes with a 10-year structural warranty that covers the hull against defects.

Hull Design
The Sailfish 30-06 CC has a deep-vee hull form with a sharp, deep entry and 24° of transom deadrise. Reverse running strakes (they turn up rather than down from garboard to chine), similar to the old Sea Craft hulls, run the length of the bottom. Its high freeboard increases seaworthiness, helping to prevent boarding seas, while providing high gunwale coamings inside the cockpit and a relatively high cockpit deck level above the waterline. ...

Click here to read the rest of the article at JDPower.com