Sailfish 30-06 CC Watertown NY

The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Navy Point Marine
(315) 646-3364
500 W Main St
Watertown, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

St Lawrence Propeller Company
(315) 639-6000
Watertown, NY
Services
Parts, Aftermarket Accessories, Supplies, Storage

Adams Chaumont Bay Marina
(315) 649-5050
11599 Circle Dr
Chaumont, NY
 
Chalks Marina & Boat Sales LLC
(315) 686-5622
18221 Reed Point Road
Fishers Landing, NY
 
Calhoun Marine & Land Service Limited
(315) 686-5390
331 Merrick St
Clayton, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

West Marine
(315) 788-8490
21214 Pioneer Plaza Dr
Watertown, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Chaumont Bay Marina
(315) 649-5050
11599 Circle Dr
Chaumont, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Magee Geordie Canvas Company
(315) 649-5018
12037 County Route 125
Chaumont, NY
Services
Parts, Aftermarket Accessories, Supplies, Storage

Northern Marine Repr Service
(315) 686-4398
16782 Stern Dr
Clayton, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Spicer Marine Basin
(315) 686-3141
40467 State Route 12
Clayton, NY
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Sailfish 30-06 CC

Provided by:

Click here for more content from JDPower.com

Model Introduction
The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Construction
The skin coat of chop in DCPD resin goes down over the gelcoat, followed by a solid hull laminate of knit fiberglass in the sides and woven roving in the bottom. The hull is supported by a fiberglass, foam-cored Compsys stringer system, and the bulkheads are also foam-cored. The whole network is encapsulated in fiberglass and bonded to the hull. The transom is built of high-density poured foam-cored transom encapsulated in fiberglass. The hull-to-deck joint is bonded with urethane adhesive and stainless self-tapping screws every foot. The rubrail and the stainless insert follows with two more rows of screws fastening the joint. The one-piece cockpit/liner is bonded to the stringers with urethane putty, becoming an integral part of the boat's structure. The cabin liner is also bonded to the hull and to the cockpit liner where they meet at the aft cabin bulkhead. The Sailfish comes with a 10-year structural warranty that covers the hull against defects.

Hull Design
The Sailfish 30-06 CC has a deep-vee hull form with a sharp, deep entry and 24° of transom deadrise. Reverse running strakes (they turn up rather than down from garboard to chine), similar to the old Sea Craft hulls, run the length of the bottom. Its high freeboard increases seaworthiness, helping to prevent boarding seas, while providing high gunwale coamings inside the cockpit and a relatively high cockpit deck level above the waterline. ...

Click here to read the rest of the article at JDPower.com